eHitter

No, the eHitter® is an all in one unit to satisfy all of your vaping needs. Our kit includes a chamber for leaf, a globe attachment for wax and a clearomizer for liquids and concentrate.

Dry blends:

1. For the best vaping results, do not pack the eHitter® ceramic heating chamber too tightly with your dried blends. Grinding always ensures an easy air flow passage for even heating and the best vaping experience.  For best results, break the dried blends up by hand or grind them. Be sure to remove all stems and/or seeds before filling the eHitter® heating chamber.

2. Dry blends ensure the best results.

3. With dry blends, in the event that vapor is not being released, use the dab tool to gently rotate the dried blends within the eHitter® chamber.

4. All replacement parts available at www.ehitter.com

Wax:

1. A little dab will do ya! Wax can be very messy so be conservative on the amout you use.

Oils and concentrate:

1. Hold the eHitter® clearomizer upside down (mouthpiece facing downward) at a 45ｰ degree angle. Lightly squeeze drops of oil into the chamber until desired dose is reached.

2.  Avoid getting oil directly into eHitter® heating element. Make certain that the liquid only surrounds the titanium cylinder and does not go inside of it.

3. When attaching the mouthpiece make sure it is snug so that it seals the eHitter® titanium chamber.

4. Remember to routinely clean your eHitter® clearomizer at the battery contact point with a cotton swab and rubbing alcohol.

Initial charge...

We recommend charging your eHitter® battery for at least 6 hours on the first charge. This will condition the battery for future battery life span.

Charging...

Charge your eHitter® vaporizer for approximately 2 hours. In the process of charging, LED indicator of the battery tip will glow (red). Once fully charged, the indicator light will turn off. Remove battery from charger once the battery is full. When the LED light on battery blinks 8 times the device needs to be recharged.

Multiple charging options...

USB charger – Connect directly to any USB port
Wall adapter – Adapts to the USB charger and to the wall
Car adapter – Adapts to the USB charger and the car
How do I Clean My eHitter® Vaporizer? -
When using the eHitter® vaporizer for an extended period of time, the filter may become clogged and dirty resulting in a difficult draw, no draw or a lower amount of vapor being released through the mouthpiece.

Cleaning the Ceramic Heating Chambers:

1. To clean the eHitter®dry herb chamber, remove the tank cover and unscrew the top of the chamber and follow directions below. To clean the eHitter® wax chamber, remove the V5 Wax Pyrex Glass Globe and follow directions below.

2. With the battery connected to the desired chamber to be cleaned, press and hold the eHitter®power button for approximately 3 to 5 seconds with the unit upside down. This should allow any excess material in the chamber to come out of the core and air channels.

3. Disconnect eHitter® atomizer from the battery

4. Use a cotton swab lightly soaked with rubbing alcohol to clean the exterior and interior heating chamber walls of the eHitter®atomizer without touching the coil. Lightly go over the air channels on the silver ring to free up any residue that may have accumulated.

5. reassemble the unit.

To clean the eHitter® Clearomizer:

1. Detach clearomizer from the  eHitter® battery. Use a cotton swab lightly soaked with rubbing alcohol to wipe away any excess oils from the connection point of the battery.

2. Remove mouthpiece and empty any remaining oils from the eHitter® clearomizer.

3. Use a cotton swab lightly soaked in alcohol to clean the inside of the  eHitter® clearomizer. Make sure to remove any residue from the base of the titanium cylinder and on the outer part of the coil. Be sure not to touch the coil.

4. Use the same process on other areas around the  eHitter® clearomizer where oils and residue has accumulated.

To clean the eHitter® Rubber Mouthpiece:

1. Use a cotton swab with rubbing alcohol and wipe the inner part of the rubber mouthpiece until clean.

2. Wipe the eHitter® mouthpiece clean with a damp paper towel.

Attach the desired eHitter chamber to the eHitter battery. Press the power button five times within 3 seconds to activate the heating element. (The LED power button will blink 3 times to insure that the unit is ON). Hold the power button down, place the plastic mouthpiece in your mouth and inhale. Enjoy your vaping experience! Your eHitter® vaporizer can be powered OFF by pressing the power button 5 times until the LED light blinks 3 times. Wait 3 seconds before activating again.

- 1 Micro-USB Battery
- 1 Tank Cover
- 1 V5 Wax Pyrex Glass Globe
- 1 V9 Dry Herb Chamber
- 1 V8 Elips Essential Oil Tank
- 1 Non-Stick Silicone Jar
- 1 Stainless Dab Tool
- 3 Silicone mouthpieces
- 1 IC Protect USB Charger
- 1 AC wall adapter
- 1 eHitter Custom Credit card grinder
- 1 User Guide

All of the eHitter® Vaporizers parts are available at www.eHitter.com or at your local authorized eHitter® dealer.